Guides
6 min readUpdated
A new floor can change the space beneath a commercial door without changing the leaf. Separate the finished surface, support condition and sealing arrangement before choosing the repair.
At a glance
- A changed finished floor can alter the relationship around a door.
- Assess the floor, threshold, support and hardware together.
- Confirm the final floor reference before approving door alterations.
Yes, the repair has to suit the finished floor
New flooring can change a commercial door repair by changing the space beneath the leaf, the threshold transition or the contact with a bottom seal. If the door stays in the same position while the surface beneath it rises, the available gap becomes smaller. The repair may therefore involve coordination with the flooring work rather than only attention to hinges or a closer.
That does not prove the flooring caused every new complaint. Worn support, a displaced leaf or another fault can exist at the same time. Before approving trimming, adjustment or replacement, establish what the finished surface will be and which part of the opening is actually interfering with it.
Record the floor change on both sides of the door
Tell the assessor whether the old finish was removed, covered or replaced, and whether the work includes underlay, levelling material or a new transition strip. A sample tile's thickness does not describe the full installed floor. Identify whether the proposal is still being selected, partly installed or complete.
Include both sides of the opening and the area through which the leaf swings. The surface directly beneath a closed door is only one location. A raised transition or a change farther along the swing path can affect movement elsewhere. Describe where staff noticed contact during ordinary use without forcing the leaf to reproduce it.
Keep loose mats and temporary floor protection separate from the permanent finish in that record. Safe existing photographs, a flooring specification and the installer's proposed finished levels are useful. Do not remove seals, lift a heavy leaf or reach beneath a moving door to obtain a more precise observation. If the opening is unstable, has damaged glass or cannot operate safely, keep people clear and notify the responsible property contact.
Separate the leaf, seal and threshold relationships
Leaf movement. Have the assessor determine whether the door itself contacts the new surface and whether its support and position are suitable. A door that dropped before the flooring work presents a different starting condition from an otherwise stable leaf facing a newly raised finish. Commercial hinge and pivot repair addresses support faults; changing support should not be assumed to be the answer to every floor conflict.
Bottom sealing. Establish whether a sweep, door shoe or automatic bottom is the part making contact. The sealing component and the leaf beneath which it is fitted are different items. Do not remove a seal merely to make the door move. Its intended function and suitability for the finished surface need to remain part of the decision.
For a product-specific example, NGP's current gasketing and automatic door-bottom catalogue, page G36 distinguishes threshold use and carpet applications without a threshold for the products shown. That illustrates why retaining the same bottom fitting after a floor change needs a compatibility check. It is not a recommendation to buy a particular seal for an unidentified door.
Threshold transition. Record whether the threshold remains at its original level, is being replaced or will sit on a different supporting surface. Also record how the adjacent finished floors meet it. A threshold can be unchanged as a component while its relationship to the walking surfaces changes. The proposed repair should consider both door movement and passage across that transition.
Include floor-mounted hardware in the planning
Where pivots or a closer are associated with the floor, identify the actual equipment before the finish around it is changed. The dormakaba BTS80 brochure, Spindles section describes extended spindle applications involving thresholds and carpeted floors. It also makes the published clearances dependent on the closer and arm being installed to the relevant template.
This is evidence that the floor relationship belongs in the equipment assessment. It does not mean an existing door can simply be raised, or that a different spindle is the appropriate repair. The technician needs to assess the support, frame, closing and securing relationships together. Give the flooring provider the confirmed hardware locations and agree how any required equipment access will remain available.
Trimming is a separate decision
Removing material from the leaf is not a universal response to reduced clearance. The Steel Door Institute's installation troubleshooting guide, section 16 says to check door and frame height relationships before alteration and to confirm with the distributor or manufacturer whether the door's design permits trimming. Its advice concerns standard steel assemblies, not permission to cut every commercial door.
Have the proposal identify the door construction, affected bottom detail and any relevant assembly documentation before material removal is considered. A familiar amount taken off another door is not an approved allowance for this one. On a labelled or documented fire or smoke assembly, ask which information supports the proposed change. The manufacturer's conditions and applicable project requirements need to be reconciled rather than replaced with a general online gap measurement.
Agree one finished condition and a provider sequence
An early door assessment can help plan the floor work, but a check against a bare substrate does not verify movement over a finish that has not yet been laid. Keep the planning visit and the final operating check distinct. If the floor specification changes after the door proposal, have the affected work reviewed before treating the original scope as settled.
Use a short decision record shared with the responsible property contact:
- Opening and starting condition: identify the door, known operating faults and what was observed before the floor work.
- Finished surface: identify the retained and new floor layers, threshold arrangement and completion stage on each side.
- Reference for the assessment: state whether each height or clearance refers to the present surface, proposed finish or completed finish. The commercial door measurement guide explains why named measurement boundaries matter.
- Agreed repair: distinguish support repair, bottom-fitting work, flooring or transition work, and any proposed leaf or frame change. State what remains unconfirmed.
- Provider sequence: assign who confirms the finished level, who prepares the surrounding work and who checks the door afterward. Confirm what can proceed while another task remains unfinished.
- Final checks and remaining questions: address the agreed movement, closing, latching and sealing functions against the completed condition. Identify any exit, accessibility or assembly requirement still awaiting project review.
Our commercial door repair service assesses the moving assembly. The record keeps that work connected to the floor provider's scope, so neither team assumes the other has resolved the doorway transition. A door that moves after an early adjustment still needs the agreed checks when the surrounding work is complete.
Questions about doors after flooring work
Should the door assessment happen before or after the new floor?
Planning before installation can identify conflicts and dependencies. Final movement and related checks need the agreed finished condition available. Explain which stage the visit covers, rather than assume one visit against an unfinished floor completes both tasks.
Does rubbing after new flooring prove that the hinges are sound?
No. The timing identifies a change to investigate, not the condition of the support hardware. The assessor should distinguish an actual floor conflict from wear, movement or another opening fault that also needs repair.
Can a stronger closer pull the door over the raised surface?
Do not use closing force as a way to overcome unidentified interference. The leaf, supports, floor and bottom fittings need assessment. Changing closer settings does not establish that the opening is suitable for continued use.
Can the old threshold stay if the flooring changes?
Possibly, but retaining the component and retaining a suitable transition are separate questions. Have its support, adjacent finished levels and relationship to the door and seal checked before retention is approved.
Is there one clearance to tell every flooring installer to leave?
No universal figure in this guide approves an opening. The identified door, hardware, floor and project requirements determine the assessment. A manufacturer's example from another application is not a site specification or an Ontario code decision.
What if the floor work changes after the repair has been agreed?
Return the revised finish and level information to the door assessor. Identify which parts of the earlier proposal depend on it, including any final check. Do not approve extra material removal simply to preserve an out-of-date arrangement.
























